---------------------------- Release notes for Repute 2.5 ---------------------------- ©2002-23 Geocentrix Ltd. All rights reserved. "Geocentrix" and "Repute" are registered trademarks of Geocentrix Ltd. Last updated: 26/10/2023 Contents: Repute 2.5 Releases 1-15 Repute 2.5 Release Candidates 1-3 Repute 2.5 Betas 1-3 Program files in the latest build Repute 2.5 release 15 --------------------- Version 2.5.15.1 Released 26/10/2023 Improvements made: 32 3889 Add the program's version number to the printed report 3888 An error occurred while reading data for 'CombinationOfActions': Error searching for expression: 'CombinationOfActions.combination_type' 3887 Provide a better implementation of Steinbrenner's treatment of a rigid layer 3886 An error ocurred while reading data ... The algorithm ... cannot be used in a boundary element analysis (... must be invariant) 3885 Hide unused tabs in Workbook 3884 Pile cap is drawn incorrectly in cross-section and elevation views 3883 Provide ability to output stiffness and flexibility coefficients in convenient format 3881 Pile group worksheet does not display controls for the piles' X or Y gradient or orientation 3878 Badly formatted error message in Borehole Wizard, Step 4 3877 Disable Message Board tabs that contain no messages 3876 Provide a "Please wait' prompt when messages take more than a few seconds to load in the Message Board 3874 Provide feedback regarding progress of multiple calculations tiggered by Build All command 3873 Remove duplicate entry for zero load in boundary increment deata (see Pile Cap worksheet) 3872 Status bar displays 'No project open' even when a project is open 3871 Setting amplification factor to 50% does not change results of Longitudinal ULS calculation 3868 Build command is disabled on Project Manager's pop-up menu when a Validation is selected 3866 Boundary element analysis is discarded on reading invalid algorithm 3864 Limit the length of any names that are displayed on the Build tab buttons 3862 Each successive boundary element analysis takes longer to complete than the previous one 3861 Badly shaped triangular pile cap 3860 Moment vs rotation graph quotes wrong units for moment axis (MNm should be kNm) 3858 Error loading XML file when analyzing pile group with surcharge 3853 Boundary element analysis fails to load XML data when water table is coincident with layer boundary 3847 Badly formatted version number in error message "This document was created in a later version (v2.500000 Release 14) ..." 3846 Internal error in 'SetCharacteristicShaftResistance' 3845 Stiffness and flexibility coefficients for bi-linear model appear as zero in the Workbook 3818 Delta value not shown in Reporter 3817 Insufficient virtual memory to preoceed (creating 2D real matrix) 3813 Handles are drawn incorrectly when pile cap is rotated on plan 3739 C++ Exception (Type uaU) on running large calculation with Coarse Granularity 3051 Dropping layer onto 'sky' part of borehole should add it above all other layers 2864 Data shown in the Workbook and Graph Paper should clear when data for calculation is changed Repute 2.5 release 14 --------------------- Version 2.5.14.1 Released 22/12/2022 Improvements made: 52 3842 Error importing data from ... : Cannot find a worksheet named '(Instructions)' (please check the import template version) 3841 Add support for igneous, sedimentary, and metamorphic rocks 3840 Error finding prototype from Id= '' when running Import Pile Group Wizard 3839 Proprty Inspector for Rock repeats "Rock, Marl" in Class drop-down box 3838 Error reading 'CombinationOfActions.combination_type'' 3835 For clarity, Property Inspector for Custom Dersign Standard should show read-only value of model factor (= 1.0) 3832 Incorrect label in beta algorithm's Property Inspector 3831 Drop-down options in rock friction Property Inspector are not read-only 3830 Zero shaft friction in drained layers when using Longitudinal ULS calculation 3828 Access violation when rotating a pile group through a user-defined angle 3824 Add separate moment vs rotation graph 3822 Increase upper limit on E1/E0 from 60% to 70% 3820 Provide option to apply resistance factors to the boundary element analysis 3819 Provide ability to specify fixed skin friction and end bearing values on a layer-by-layer basis 3812 Error 1606. Could not access network location [Chinese characters] \. when installing via SCCM 3811 Do you want to allow this app from an unknown publisher to make changes to your device? 3810 Add option to calculate wall friction from tan(delta)/tan(phi) ratio 3808 Implement Resistance Factor Approach in Boundary Element Analysis 3807 Simplify the presentation of partial factors ahread of the 2nd Generation Eurocodes 3802 Cannot change graph using the Pile Group drop-down box on the Graph Paper tab 3798 Program cannot get licence from server running legacy Gemalto Sentinel Runtime Environment 3795 Issue warning when horizontal forces or moments are applied in single pile calculation 3794 Add a button to the Tools menu to Renew Licence 3793 Pile cap depth is not set on opening RPX file 3777 Implement Australian Standard AS 2159 Piling - Design and installation 3774 Allow a pile's Material Name and Section Name to be changed in the Workbook 3689 Add Run Diagnostics command to Tools menu 3647 Add enhaced diagnostics to the Tools menu 3529 Provide ability to import load combinations (instead of individual actions) 3465 Drawing Board goes black for a long time when opening a large file 3313 Offending items are not specified in error message "Some items extend beyond the drawing in the z directions(s)" 3292 Warning: some items extend beyond the drawing in the z directions(s) 3289 Add labels next to borehole to identify layers and soils 3226 Add option to display levels (m OD) on rulers instead of depths (m) 3057 Scale the drawing of forces according to their magnitude 3055 Selection handles are not drawn correctly when the force arrow is pointing upwards 3053 Add option to display borehole on both sides of Drawing Board 3052 Add ability to display borehole in actual position on Drawing Board 3029 Provide support for Australian Standard AS 2159-2009 2851 Add algorithm to implement Horvarth and Kenney's skin friction relationship for rocks 2842 Add more algorithms for end-bearing and frictional resistance estimation in rock 2820 Provide ability to rotate the pile group by an arbitrary amount 2816 Change 'Soil type' to 'Soil/rock' type throughout the program 2698 Add further roles to Client item (e.g. geotechnical engineer) 2457 Allow direct input of limiting stresses for rock layers 2383 Project created by Project Wizard is not added to recent projects list when closed 2289 Program forgets commands added to Quick Access Toolbar 1990 Draw horizontal lines across drawing to indicate boundaries between layers 1983 Add support for Australian Piling Code AS2159 1869 Drawing of moments and forces should be scaled according to their magnitude 1854 Improve drawing of observation point 1421 Provide ability to view text output from PGroupN within Repute Repute 2.5 release 13 --------------------- Version 2.5.13.1 Released 22/06/2022 Improvements made: 40 3792 Update Sentinel Runtime Environment to v8.43 (June 2022 release) 3791 Extend the Import Load Wizard so that it can read multiple combinations of actions 3790 Add hatching below ground surface in cross-section orientation 3789 Do not change scale when switching to/from plan orientation 3788 Add third axis to Drawing Board's axis indicator 3787 Hit-testing doesn't take account of pile rake 3785 Sign of pile rake in y-direction is reversed in boundary element analyses 3782 An error occurred while reading data for 'Chalk': Chk 3780 Default Young's modulus for Custom Concrete should be 10 GPa, not 10 MPa 3779 Import Wizards cannot read value specified by formula in Excel 3776 On re-opening RPX file, compressive strength of Custom concrete is shown as cylinder strength even when saved as cube strength 3773 Cannot import 600 mm diameter spun piles via Import Pile Group Wizard 3767 Boundary element analysis generates no results when user's name takes the form "xxxxxxx.xxxxx" 3765 Extend the Import Pile Group Wizard to support for H-, pipe, and spun pipe sections 3764 The Import Loads Group Wizard should add notes to all actions indicating the Excel file used to import them 3763 The Import Pile Group Wizard should add notes to all piles indicating the Excel file used to import them 3762 Calculation Wizard lists Fleming's Analaysis twice on page 1 3761 Borehole Wizard does not create layer when soil's shear modulus is invalid 3758 Program crashes calculating Longitudinal ULS with two different Alpha algorithms 3757 Strength gradient is incorrectly labelled as "cu.ref2" in the soil's Property Inspector 3754 Cannot edit model factor on resistance for EN 1997-1:2004 design standard 3750 C++ Exception (Type ) when selecting Borehole containing layer with missing soil 3749 Error while reading data for 'Chalk': Chk6 3748 Graph of results of Randolph's Analysis shows reduction in stratum thickness, not total settlement 3747 Data disappears from graph when graph options are loaded 3746 An error occurred while reading data ... The algorithm ... cannot be used in a boundary element analysis (... must be invariant) 3745 Custom concrete with specified cube strength is saved with cylinder strength instead 3744 An error occurred while reading data for 'BSEN1997_2004': Error searching for expression: 'EN1997_2004.amendment' in file '' 3743 Copy command in Message Board popup menu does not work 3742 "Cannot focus a disabled or invisible window" when running the Borehole Wizard 3738 Add the bearing capacity algorithm (ERTC3) used by the boundary element engine 3735 Pile Group Wizard creates multiple identical sections when generating spun piles 3734 Error message: abnormal program termination on program startup 3733 Bearing capacity algorithm sets Nq = 0 (instead of custom value) in boundary element engine 3731 Failed to load XML data. Reason: Error loading XML document: Validate failed because the document does not contain exactly one root node 3718 Add Select All command to Project Manager 3660 Right-clicking on an item in the Project Manager does not select it 3658 Remove excess files from setup program 3656 Rename "Pile interaction" as “Maximum interaction distance” in Boundary Element Analysis's property inspector 3630 Add ability for dongle PIN to be displayed as decimal value (as well as hex value) Repute 2.5 release 12 --------------------- Version 2.5.12.3 Released 25/02/2022 Improvements made: 48 3732 Options provided for Combination type in Combination of Actions Property Inspector are wrong 3725 Self-weight of pile cap is not factored in Boundary Element Analysis 3724 Boundary Element Engine truncates filenames containing "." 3722 Access violation in module 'ntdll.dll'. Read of address 00000000 3719 Error dragging item from Stockyard of one instance of program to Project Manager of another instance 3716 Extend Randolph's Analysis to cater for other pile types than just bored 3715 HASP Library version number is incorrectly reported 3714 Remove limitation on degrees of freedom (currently 8000) in Boundary Element Analysis 3713 Increase the available program memory on 64-bit Windows to 3 GB 3712 Boundary Element Analysis's Automatic Precision flag should be turned off when its Mesh Granularity is changed 3711 Failed to load XML data. Reason: Error loading XML document: Validate failed because the document does not contain exactly one root node 3710 Improve error message that Fleming's and Randolph's Analyses are not available for Spun Pile 3708 Add density index to coarse soils to support algorithms that require them 3707 Add plasticity index to fine soils to support algorithms that require it 3706 Clarify the strain level used to specify G1 3705 Failed to load XML data (Error creating matrices!) 3703 Update Sentinel API libraries to v8.3 3697 Extend automatic saving of workbook layout to individual columns 3694 Add Build command to Project Manager's popup menu when a calculation is selected 3693 Longitudinal ULS calculation does not take account of Ks algorithm linked to the calculation 3691 No longer possible to apply skin friction limit algorithm to a layer 3671 Add controls to Property Inspector to display partial factors applied in pile group analysis 3669 Provide a fast way of customizing column headings in the Workbook 3668 Grade and Path appear above Name in Property Inspector for concrete 3667 Error reading XML file: no nodes found (when drag-dropping items between separate instances of Repute) 3665 Pile graphs only show positive values of displacement by default 3664 Provide beta algorithms based on formulae published by McClelland, Meyerhof, and Kraft and Lyons 3663 Add ability to set constant value of skin friction and bearing pressure for rock 3662 Validation does not detect missing material in bored pile 3661 No Contact algorithm causes Randolph calculation to issue "Not specified" error 3656 Rename "Pile interaction" as “Limiting pile interaction distance” in Boundary Element Analysis's property inspector 3653 Failed to load XML data. Reason: Error loading XML document: Validate failed because the document does not contain exactly one root node 3651 Reinstate minimum and maximum values for Shear and Torque columns in Workbook 3649 Add ability to reset program settings to factory values 3646 Add instructions how to renew expried ReAssurance 3638 Temporary files output from boundary element engine have extensions truncated by one letter 3637 Update Developer Express controls to v21.1.5 3635 Update DropMaster control to v2.5.2 3634 No [boundary element] results have been generated or saved for 'Calculation Acc' (file extensions truncated) 3633 Add ability to set Diagnostics flag via Program Options box 3632 Update FastReports to v2021.3 3631 Update Steema TChart control to v9.33 3629 Update FastReports to v2021.3 3584 Invalid argument to Berezantzev's algorithm when transferring data to boundary element engine 3583 Update Developer Express VCL to v21.1.5 3559 Add facility to rotate pile group by an arbitrary angle 3541 Add the ability to create a Chin plot for Fleming's Analysis 1362 Scroll wheel does not work in Reporter Repute 2.5 release 11 --------------------- Version 2.5.11.21071 Released 02/08/2021 Improvements made: 50 3622 Trial Edition banner appears off centre on Drawing Board 3620 Missing LIC file causes splash screen to load repeatedly on program startup 3619 Details of mesh granularity used in Boundary Element Analysis are not given in Reference Manual 3618 Longitudinal ULS calculation ignores beta algorithm specified in soil layers 3617 Should not be able to scroll the graph (vertically) by rotating the mouse wheel 3615 'No material has been specified' error on creating new Bored Pile 3614 Error message for lower bound values for custom rock algorithms should read >= 3613 Details of rock algorithm missing from Reference Manual 3611 Error loading licence ... Could not find the MAC address of this computer's network card 3609 Access violation on opening RPX file via Windows File Explorer 3608 Program crashes running boundary element analysis with Maths Kernel Libraries flag on 3607 Material not specified for layer 'Layer 2' when showing stiffness graph 3606 External exception EEFACE when selecting borehole containing rigid layer 3605 Access violation when opening RPX file created in Release 9 3604 Access violation ... in module 'Repute2.exe' when running boundary element analysis using Maths Kernel Libraries 3603 An error occurred while reading data for 'BS8004_1986': Error in selecting values using XML query 'BS8004.factor_on_bearing_resistance' ... 3602 Invalid data in sheet 'AB2', row 6 onwards 3601 Visual Fortran run-time error, severe (66) output statement overflows record, unit 6 3600 Transverse displacement and twist at the pile to should be "not available" not zero (in both graph and workbook) 3599 Program crashes running over SSL-VPN 3593 Cannot enter concrete Young's Modulus greater than 60 GPa or strength equal to 88 MPa 3591 Error reading XML file: Nc must be between 5.14159 and 266. Value entered = 5.14159 3590 Splash screen flashes repeatedly on program startup 3588 Outer piles deflect inwards towards the centre of the pile group under vertical force only 3587 RPX file contains many thousands of blank lines following import of actions 3586 Internal error: no XML reader has been registered for 'Extents' 3585 Degree of utilization is displayed as a ratio not as a percent 3578 Pile Group Wizard fails to set the depth of the pile group when an upstand is specified 3576 Cannot display pile's Property Inspector when pile has no material specified 3575 "No contact algorithm" is still referred to as "Shrinkage Algorithm" in the Reference Manual 3567 Randolph's Analysis gives 27 mm settlement vs 2 mm from boundary element analysis 3564 Software takes a long time to start up when run across a VPN connection 3563 Program hangs with black screen on generating report 3546 Allow limiting skin friction to be applied to the average skin friction in a layer 3542 Cannot remove a soil from a Soil Layer 3522 Change back end of PGroupN-Win to BoundaryElementEngine.dll 3517 Prevent scrolling of Graph Paper going beyond graph extents 3505 Add facility for Repute to open import templates in Excel 3490 Program crashes on renewing licence when trial licence is currently installed 3435 Default k3 and k4 values are quoted incorrectly in Reference Manual, page 11 3379 Shear stress value at bottom of each pile is misleading 3343 Licence reverts back to old details on restarting program 3303 Change graph background to white 3247 boost::filesystem::exists: The device is not ready 3132 Display boundary element results for the pile toe separately from those for the pile shaft 3103 Allow user to drop RPX file onto application to open it 3096 Warning: tr1::bad_weak_ptr when changing soil stiffness 3054 Double-clicking on an item in the Stockyard does not create that item 3011 Warning "tr1::bad_weak_ptr" when entering Poisson's ratio 2984 Items are prompted for deletion even when not selected in Project Manager Repute 2.5 release 10 --------------------- Version 2.5.10.20211 Released 27/04/2021 Improvements made: 74 3573 Number of pile elements must be >=3 and <= 50. Value entered = 5 3571 Borehole Wizard calculates wrong reference depths for clay below sand 3570 Young's modulus at 1 % strain must be >= 30 MPa and <= 5.19615 MPa. Value entered = 60 MPa 3568 Longitudinal ULS calculation does not use Poulos and Bunce to calculate default alpha 3565 Randolph's Analysis does not use Poisson's ratio of 0.5 in undrained analysis 3560 Rename Workbook's Boundary Element and Boundary Increment tabs 3558 Ambiguity in Reference Manual regarding default values of earth and bearing pressure coefficients 3557 Add display of combination factors to Design Standard Property Inspector 3556 Remove unused values from RPX file regarding values of partial factors 3555 Move the axes indicator to the top left of the plan drawing 3554 Error "Results are not available for element at depth < -0.25 m" when displaying Shear stress graph 3553 Worksheet for combination of actions does not display any data 3552 Add column for Material Properties to Pile Group worksheet 3551 Pile Group Wizard does not rotate the pile cap with the piles 3549 Increase the number of piles that can be created by the Pile Group Wizard 3547 Add classification of combination of actions (e.g. quasi-permanent, transient, etc) 3538 Rename "Clean Up Program Data" command as "Delete Temporary Files" 3536 Top button in layer selection box is pointing in the wrong direction 3535 The Drawing Board should differentiate steel and concrete by colour 3533 Specify which stiffness is shown in the graph of borehole stiffness 3532 Error message "Invalid data in sheet '', row 12" refers to the wrong row 3525 Increase the number of actions that can be entered via the ActionWizard to 50 3524 Example project 'Large pile group' does not include small strain stiffnesses needed for analysis 3523 RPX files for Tutorials 1-3 are corrupted in Release 6 3520 Cannot identify Es value in error message "The pile/soil stiffness ratio ... is less than 5 ... Es = 6.875 GPa ...)" 3519 An error occurred while reading data for clay (FineSoil.strength/UndrainedStrength.strength) in v2.5.6 RPX file 3518 Save boundary element results as ^.ext instead of in folder { ProjectName } 3516 Workbook's Combination of Actions page does not show any data 3514 Improve wording of 'Reading data from ... XML node' messages created on opening RPX file 3513 Replace PGroupN executable with dynamic link library 3512 Young's modulus at 1 % strain must be >= 41.69 MPa and <= 26.3873 MPa. Value entered = 80.19 MPa 3510 Failed to install hardlock.cat signature 3509 Update Sentinel HASP/LDK Windows Command Line Run-time Installer to version 8.15 3508 Update Sentinel HASP/LDK Windows GUI Run-time Installer to version 8.15 3507 Template for importing actions that is installed in C:\Program Files (x86) is an out-of-date version 3506 User Manual gives wrong folder for import templates 3503 Provide maximum bending moment and shear force for each pile in the Boundary Elements worksheet 3502 Provide values for settlement in each layer in Randolph Analysis 3499 Cannot select a rock in the Drawing Board's borehole 3498 Demote "Radial influence factor (zeta) out of range" to warning in Randolph calculation 3497 Number of pile elements is calculated incorrectly when a combination of actions with Fz = 0 is applied 3496 Graph is cut off due to automatic scaling option not set for top axis 3495 Remove Temp folder from ProgramData\Geocentrix\Repute\2.5 3494 Rename UI.ini and MRU.ini configuration files 3492 Micropile details are missing from the Report 3491 Property Inspector will not accept Emax = 36.8MPa at 20.25 m with Emin = 5 MPa specified at 0.25 m 3488 Exported Excel spreadsheet names tab "Users " 3487 Water table line only extends over the left hand side of the Drawing Board 3485 Algorithm report does not include values of limiting skin friction and base pressure 3484 Add to Workbook the display of axial and largest (normal) shear force and bending moment 3482 Value of wall friction not given in Report 3481 Add key for symbols fslim, qblim, alpha, delta, and Ks in the Reporter 3479 Soil and rock data should appear before last page of report 3478 Boundary element shear stress graph should not display base pressure 3477 Message reports only 27 load increments have been read from Output.xml file 3475 Add support for variable pile stiffness 3405 Provide ability to model partially infilled pile 3378 Clarify that resultant forces and displacements in raked piles are given in local coordinates 3344 Change name of 'Standing Water' to 'Surface Water' in line with 2nd generation of Eurocode 7 3305 The ratio of the larger to smaller stiffness moduli must be >= 0 and <= 10. Value entered = 1001 3294 Windows Application Error when opening Quick-Start Tutorial from Tools tab 3258 Allow pile cap to be rotated on plan 3235 Allow stiffness values to be entered via Borehole Wizard 3206 Allows names to be specified in Action Wizard 3199 Add a Custom Rock item 3149 Bug in PGroupN code in CalcStiffnessDisplsStressesLoads.f90 3078 "'hr': Type mismatch" error on opening RPX file 3070 Allow soil and rock stiffness to be set in Borehole Wizard 3056 Distinguish between permanent/variable/accidental/seismic actions when drawing forces and moments 3043 Allow names to be specified for actions created by Action Wizard 3021 Show the inclination and orientation of forces and moments in the Property Inspector 2987 Add Program Option to clear old messages from Message Board on creating or opening a new project 2724 Allow actions to be classified as 'wind', 'ice', etc. as per Eurocodes 2343 Remove redundant properties from RandolphAnalaysis Repute 2.5 release 9 -------------------- Version 2.5.9.20101 Released 16/10/2020 Issues fixed (42 items): 3469 Key to Fz vs depth graph does not display name of piles, only their 'index' 3468 tr1::bad_weak_ptr on changing value of soil stiffness 3467 Invalid characters in key for load vs displacement graph 3466 Buttons on Graph Paper tab are not labelled correctly when a borehole is selected in the Project Manager 3464 Error "Ground stiffness not specified" when changing type in Property Inspector 3463 Update reporting control to FastReport 6.7.9 3462 Invalid pile type (Pipe Pile) specified in Fleming's Analysis 3458 Cannot enter value for Pile cap breadth in y-direction 3457 Automatically generate a report on opening the Reporter 3450 Simplify and generalize custom design standards 3448 Section properties (such as A, EA, GJ etc) are missing from micropile Property Inspector 3440 Partial factors are not applied to boundary element analysis when using custom design standard 3439 Move report template from Program Files to to ProgramData folder 3438 Reporter tab does not get focus when Reporter is opened 3436 Rock pressure coefficient k5 incorrectly labelled "kr" in Property Inspector 3434 Add colour-coding to messages in the Message Board 3433 Provide facility to turn sounds on or off 3432 Message Board displays "bad lexical cast: source type value could not be interpreted as target" at program startup 3431 Partial factors for BS EN 1997-1 and BS 8004:2015 are those for EN 1997-1 3423 Enable renewal of licence from the Internet 3422 Moments and forces are not imported into Repute 3420 Maximum cube strength for custom concrete should be greater than 60 MPa 3418 Update cURL library to v7.71.1 3417 Update zlib1 compression library to v2.2.11.0 3415 Error "BaseResistanceFactorSetR4" on saving project with NTC08 design standard 3414 Error finding prototype from Id = 'Bored pile' 3413 Invalid data in sheet '', row 3: Pile length must be >= 2 m and <= 126.1 m. Value entered = 0 m 3412 Project Manager should remove headings with nothing underneath them 3411 Error searching for expression: 'FineSoil.strength/UndrainedStrength.base_strength' in file created in v2.5.6 3410 Update drag/drop control to Raize DropMaster 2.5.1 3409 Update Sentinel HASP library to version 8.11 3408 Update graphing control to FastReports v6.7.9 3407 Update Steema TeeChart to v9.30.200525 (i.e. 2020.30) 3406 Update Developer Express controls VCL to v20.1.3 3403 On closing project, get error message "boost::filesystem::copy_file: The system cannot find the file specified" 3385 Rock materials do not show on the ‘Review’ tab 3317 Cannot create file "... infilled pipe pile.rpx". The request is not supported 3302 Add sub-headings to Project Manager tree control 3277 Print icon within the Reporter tab does not create any output 3270 Data import takes a long time with many (> 200) piles 3256 Error on importing spreadsheet "Could not convert variant of type (UnicodeString) into type (Double)" 3190 Log file is produced by release version of PGroupN 2801 tr1::bad_weak_ptr when classifying newly created Clay as 'saCl' 962 Improve the aural feedback for warnings and errors, etc Repute 2.5 release 8 -------------------- Version 2.5.8.20071 Released 29/07/2020 Issues fixed (37 items): 3404 A 'ping' sound is emitted by the computer whenever a warning message is generated 3393 Shear stress utliization should be presented as an absolute (i.e. non-negative) value 3386 Error on program start: There is no Geocentrix network licence key at address 'ass_id ="0" tracking_level (etc) 3377 Caption should indicate whether program is logged in or not 3376 Network licence has suddenly stopped working 3375 There is no Geocentrix licence key at address ... 3373 Horizontal Young's modulus of soil does not change on changing anisotropy 3372 Exported 'Boundary Elements' spreadsheet is corrupted on opening in Excel 3371 Provide better explanation of Sentinel error message 27 - "Program running on a terminal server" 3370 Fleming Analysis's shrinkage algorithm is lost on saving RPX file 3369 Boundary Element Analysis's plugging algorithm is lost on re-opening RPX file 3368 Cannot set alpha algorithm for soils in Longitudinal ULS Property Inspector 3367 Algorithms should appear under the same Property Inspector heading for all calculations 3366 Example Randolph calculation does not reproduce book example 3365 Provide a more appropriate name for the Shrinkage algorithm 3364 Cannot change the value of G/E @ zmax in the soil's Property Inspector 3363 Uniform surcharge does not have any influence on boundary element results 3362 Surcharge is missing on re-opening project (RPX) file 3361 Show commands for C2V and V2C files only when enabled in Program Options 3360 Randolph Analaysis with two layers gives settlement twice that with one layer 3359 Discrepancy in calculation of elastic shortening via Fleming's Analysis 3358 Program miscalculates the value of g in Fleming's analysis 3355 Error on re-opening exported Excel spreadsheet containing data evaluating as 'INF' 3354 Error on saving modified file: "boost::filesystem::copy_file: The system cannot find the file specified" 3353 Access violation on changing name of item in Property Inspector 3352 Access violation on changing Ground Stiffness to 'Constant stiffness' 3342 Splash screen remains hidden instead of closing after startup 3341 Error message "Session been interrupted (Status = 39)" does not reset commands on Licence tab 3339 Repute2.lic should not be saved to disk if no changes are made to it 3338 Licence backup files are misnamed as " - Copy (2).lic" etc 3337 Partial factors for BS EN 1997-1:2004+A1:2013 are not the same as 2014 UK National Annex for accidental design situation 3336 Program is out of memory after 15 minutes if licence uses MAC address 3314 Better explanation needed for "Input error: double raked piles under torque need same absolure X and Y rakes" 3310 Program does not display its login status on the application's title bar 3210 sqrt: DOMAIN error when adding uniform surcharge to combination of actions 3181 Unable to run Repute Trial Edition 3124 Licence acquisition times out when network has poor connectivity Repute 2.5 release 7 -------------------- Version 2.5.7.20021 Released 19/02/2020 Issues fixed (20 items): 3334 MRU list is not updated on exiting the program 3333 RPX files provided for Tutorials 1 and 2 are not well-formed 3331 Update graph control to Steema TeeChart VCL32 v2020.29 3330 Update reporting control to FastReport v6.5.1 3329 Update user interface controls to Developer Express VCL v19.2.4 3328 Hyperbolic boundary element analysis sets incorrect wall friction value when no algorithm is specified 3324 Access violation when importing pile group data via Wizard 3323 Program does not ship with revised template needed for import into version 2.5 release 6 3322 Pile-soil interface friction passed to PGN file is 1 deg 3321 An error occurred while reading data for 'Clay': 2541 3320 An error occurred while reading data from v2.5.3 RPX file for 'Clay' when undrained strength increases with depth 3318 Cannot enter unconfined compressive strength less than 5 MPa for rock unless Strict Validation flag is turned off 3316 Cannot deselect infill material from Pipe Pile 3315 Rock no longer appears in dropdown list of soil/rock types in Borehole Wizard 3309 Failed to install hardlock.cat signature 3308 Longitudinal ULS calculation ignores skin friction and end bearing of rock layers 3307 Property Inspector for Longitudinal ULS calculation does not allow rock friction or rock bearing algorithms to be specified 3306 Image overlaps progress bar and buttons in Repute Setup 3232 Warning 'tr1::bad_weak_ptr' on changing unconfined strength of rock 3201 boost::weak_ptr on changing density of clay (Training Course workshop) Repute 2.5 release 6 -------------------- Version 2.5.6.19092 Released 20/12/2019 Issues fixed (35 items): 3301 Unexpected error message "Some items extend beyond the drawing..." 3298 Improve clarity of error message "Too many concurrent users" 3297 Ultimate axial capacity of pile exceeded by tension pile in rock 3296 Different results obtained from v2.5 Release 5 compared with Releases 2 and 4 3295 Cannot find HASPUserSetup.exe 3293 Convert stiffness from old RPX files to new format 3291 Amplification factor for combination of action is not set on opening project file 3290 Simplify entry of small strain and large strain stiffnesses 3287 Input error: bearing capacity factors Nq flag is not 1 or 2 3286 Intel(r) Visual Fortran run-time error 3284 Add support for pipe pile with concrete infill 3283 Add compiler name and version to About box's technical information 3282 Relocate temporary PGroupN files in Windows TEMP folder 3281 Atmospheric pressure for rock algorithms set incorrectly on opening RPX file 3280 Ultimate capacity of pile group exceeded when pile is founded in rock but not in weak deposits 3279 In boundary element analyses, rock is treated as soil, unless it is placed in a Rock Layer 3278 Same results are obtained after changing loads without saving and re-opening RPX file 3275 Sorting items does not mark project as needing to be saved 3274 Intel Visual Fortran run-time error when running BEA with infinite bearing pressure limit 3271 Cannot find Sentinel LDK/HASP Runtime setup program 'C:/Program Files (x86)/Geocentrix/HASPUserSetup.exe' 3269 Workbook does not allow Notes to be displayed on its Combination of Action page 3268 Add ability to update pile properties via Pile Group Import Wizard 3266 Allow forces and moments to be specified in single row in load import spreadsheet 3265 Import Loads Wizard should ignore forces and moments that have zero magnitude 3264 Add ability to show grid lines on plan 3262 Curl error 7: Failed to connect to host or proxy 3259 Display the total number of piles in the pile group in its Property Inspector 3252 Program automatically generates many algorithms for each boundary element analysis 3251 Abnormal program termination when importing pile group specifying 'Augered' pile type 3250 BEM analysis uses large-strain Es after switching stress-strain model from bi-linear to hyperbolic 3249 Error reading non-linear layer when running boundary element analysis with earth pressure algorithm 3248 Error reading non-linear layer 3246 Build number always written as '1' in RPX file's tag 3229 Changes to the parameters of FlemingAnalysis do not clear old results 2800 Ruler shows ground level at -8.5m for pile group with raked piles with upstand Repute 2.5 release 5 -------------------- Version 2.5.5.19080 Released 07/08/2019 Issues fixed (44 items): 3244 Algorithms do not need to be created when opening legacy linear-elastic Boundary Element Analysis 3243 Base diameter of bored pile is set to default value (600 mm) when imported via Wizard if shaft diameter is smaller 3241 Borehole is drawn above ground level when an upstand pile and standing water are present 3239 Provide function to remove duplicate items from a project file 3236 Allow depth of each action to be specified in the Action Wizard 3234 Move obscure/legacy Boundary Element Analysis options to 'Advanced Options' group 3233 'Not specified' error in Drawing Board when Pipe Pile or Spun Pile has no section specified 3231 Micropiles specified with diameter 300 mm are lost on re-opening RPX file 3230 Provide algorithms for shaft friction and end bearing in rock 3228 Borehole does not refresh automatically when selecting a new layer in the Layer Selection box 3227 By default, hide the effective cohesion column from Workbook display for Longitudinal ULS calculation 3225 Duplicate command appends '- Copy' to previously duplicated items instead of '- Copy (n)' 3224 Internal error: no XML reader has been registed for 'RockFrictionAlgorithm' 3221 Error in calculation of elastic section modulus for minor axis 3220 Minor improvements to Bearing Pile Property Inspector 3219 Automatically write error messages to the program's log 3216 Allow interface adhesion value in Boundary Element Analysis to be specified via algorithm 3215 Revise the alpha algorithm to include the Kolk and van der Velde (1996) method 3214 Cannot increase diameter of Custom Pipe Section from default value 3209 Input error: invalid delta specified for drained soil layer 3208 Revise maximum skin friction limit to match CIRIA C574 value for chalk 3205 Workbook display of borehole properties has gone awry 3203 Cannot enter custom value directly into Bearing Capacity Factor algorithm Property Inspector 3197 Pile Group Wizard is disabled in Trial Edition (but is needed for Tutorial 4) 3193 Include the program's build number in the RPX file 3188 Display licence number from RPX file when opening that file 3186 Vertical displacement is reported incorrectly in Reporter 3182 Change items available in Trial Edition via Stockyard 3181 Unable to run Repute Trial Edition 3180 Network settings are not preserved when importing new licence (.LIC) file 3175 Cannot specify custom spun pile section with diameter > 600 mm 3174 Load on single pile ignores combination of actions (just considers self-weight) 3173 Boundary element analysis includes applied forces twice when a design standard is linked to it 3172 Add warning message to inform the user if they are not running the latest release 3171 Add current release to message stating "The latest release of this program is ..." 3170 Piglet XLS conversion wizard cannot read spreadsheet with additional page inserted at beginning 3169 Error message "Can only convert Piglet v5.1 files. File versions in -NAN" 3104 Prevent user from entering Fx = Fy = Fz = 0 into Action Wizard 3081 Allow skin friction and end-bearing values in Boundary Element Analysis to be specified via algorithms 3032 Cannot switch Berezantsev bearing capacity algorithm to Custom option just by typing custom value 2983 Provide "Yes to All/No to All" options when deleting multiple items in the Project Manager 2924 Provide algorithms to support Poulos's equations for calcuating pile capacity in rock 2905 Cannot perform ULS verification on pile group containing one pile 2499 Provide section properties for European wide flange beams Repute 2.5 release 4 -------------------- Version 2.5.4.18100 Released 21/11/2018 Issues fixed (48 items): 3167 Spurious values given for minimum and maximum pile rotation in Reporter 3166 Wrong font displayed in the Reference Manual 3163 Program does not show welcome screen on startup 3162 Reporter does not display value of dG/dz for soils 3161 Extend action import capability to include variability 3160 Allow server IP address to be specified using hostname 3159 Make Tutorials available for download from the Geocentrix website 3158 Spreadsheet exported from boundary elements worksheet has very large footer rows 3151 Allow bored pile diameters greater than 3000 mm to be entered 3150 Changing the stiffness of a duplicated soil also change the stiffness of the soil it duplicates 3147 Add support for the latest range of ICP spun piles 3146 Borehole is not drawn at correct elevation 3145 A 'ghost' (white) tubular pile appears at the plan centre of the pile group 3143 Improve feedback when boost::filesystem::create_directory error occurs 3142 Provide better error handling when saved boundary element results are corrupted 3141 Piles lengths do not change in Workbook according to instructions given in User Manual pp35-36 3136 Graph does not display results after building the current scenario 3135 Allow multiple items to be deleted by answering 'Yes to All' in dialog box 3134 Access violation on deleting two or more scenarios or calculations from the Project Manager 3130 An error occurred while reading data for 'StockPipeSection': Outside diameter must be >= 333.333 mm and <= 3657.6 mm. Value entered = 219.1 mm 3129 Add support for saving Workbook results in Excel's XLSX format 3128 Display Release number in splash screen 3127 Error 1606. Could not access network location ?y?yS_VERSION_INFO\Repute Projects 3126 Error on opening Repute 1.x file: "Number of pile elements must be >= 3 and <= 3. Value entered = 10" 3125 Unable to change the pile cap thickness 3123 Design base resistance (Rbd) does not account for the calculation's bearing pressure limit 3118 Top of borehole is drawn at 6 m above ground level 3117 Change the name of the boundary element analysis "linear-elastic/perfectly-plastic" model to "bi-linear" 3116 Change the default stress-strain model for the boundary element analysis to bi-linear 3115 Access violation when opening RPX file by double-clicking on it in Windows' File Manager 3114 Access violation when validating boundary element analysis in which pile/soil stiffness ratio is less than 5 3112 Access violation when running a boundary element analysis that generates an error during validation 3109 Splash screen does not appear on program startup 3108 Access Violation on validating undrained calculation using Chalk 3107 Invalid default value in Pile Group Wizard 3106 Text is out of date in Quick Start Guide, Tutorial 6 Step 2, bullet 10 3105 Clarify in the Quick-start Guide the need to click on Pile Group 1 in order to view its properties in the Property Inspector 3102 Rulers are not drawn properly on program startup 3100 Automatically create backup of existing licence when importing/editing licence 3099 Create backup of existing licence when changing licence details 3083 Allow network licence to be specified using hostname instead of IP address 3073 Improve error message when Hyperbolic BEM cannot find small strain stiffness 3008 Program opens files via File Manager without valid licence being present 2938 Allow the plan location of forces/moments to be tied to the locations of the piles 1713 Add single-pile design capabilities for tubular piles 1365 Add plots of tip resistance and shaft friction vs vertical displacement 792 Allow multiple load paths to be applied one after the other (rather than a single load path being applied) 760 Show maximum bending moments & forces along piles in "Key Results" report Repute 2.5 release 3 -------------------- Version 2.5.3.18031 Released 07/06/2018 Issues fixed (40 items): 3097 Access violation in module Scenarios.dll when deleting concrete from Project Manager 3093 Option 'Generate C2V file for HASP key' is not available from Sentinel Admin Control Centre 3092 Error searching for expression: 'AnnularSection.wall_thickness' 3091 Repute 2.5 Release 2 runs slowly across large Wide Area Networks 3089 Allow Repute setup program to run silently without prompting to install the Gemalto Sentinel drivers 3088 Plastic section modulus of pipe section is incorrect 3087 Boundary element analysis fails with message 'Error reading flags' 3085 Default weight density and angle of shearing resistance in Borehole Wizard do not match screenshot in Quick-Start Tutorial 3076 Increase minimum cover for pile cap to 50 mm and default to 150 mm 3074 Import Loads Wizard does not import the names of moments 3071 Action Wizard crashes after entering Force = (0, 0, 0) in Step 2 3069 Rotate commands perform apparently random rotations on pile group 3068 Add columns to Workbook to display pile base and shaft areas (in addition to equivalent diameters) 3067 Formula for Fleming's Analysis in Reference Manual is in error 3066 Add ability to save user interface changes from one session to the next 3065 Allow different plan shapes of pile cap (triangular/hexagonal/circular) to be specified 3064 Automatically increase/decrease scale on switching to/from Plan view 3063 Enhance 'Retrieve data from key' command to include ReAssurance details 3062 Error 'Not specified' when generating report containing a non-Custom alpha algorithm 3061 Increase the limit on pile length from 70 m to 126.1 m 3060 Longitudinal ULS Property Inspector allows beta algorithm to be selected at same time as Ks and delta algorithms 3059 Add support for LDSA Guidance Notes for ... Bored Piles in London Clay 3050 Split 'Links' group into 'Links' and 'Algorithms' 3048 List index out of bounds when changing Free-Standing Length of several piles in Workbook 3046 Pile orientation does not match the orientation of the pile group when created in the Pile Group Wizard 3042 Drawing Board does not display H-piles with proper orientation 3035 'Permanent' group is collapse on opening Property Inspector for Combination of Actions 3034 Change units for rock unconfined compressive strength to MPa in Borehole Wizard Step 4 3033 Item in Stockyard can be dragged into Project Manager even when disabled (applies to Trial edition) 3031 Cannot deselect limiting skin friction or end bearing algorithms 3028 Arrow depicting uniform surcharge is drawn too large 3019 Caption for Step 3. Enter the pile length and upstand should read 'Step 4' 3017 Warning message 'Using default value for alpha' appears multiple times in the Message Board 3016 Program is disabled when Trial Edition is selected 3013 Repute is slow or does not respond after running non-linear BEM analysis for pile group 3012 Reporter displays incorrect information 3009 Rock is always treated as drained soil in ULS verification 3007 Error occurred reading expression: 'CustomEN1997.factor_on_shearing_resistance' in RPX file from 2.0.22 2963 Display HASP API version in About Box credits screen 2935 The installer has insufficient privileges to modify this file: C:\ProgramData\Geocentrix\Repute2.log Repute 2.5 release 2 -------------------- Version 2.5.2.17138 Released 20/12/2017 Issues fixed (41 items): 3001 Maximum length of spun pile (= 18 m) is too limiting for practical use 2998 Unable to display the Reporter - error 'Not specified' 2997 Arrow head for moment points in wrong direction in combination of actions 2996 Program crashes with message "Assertion failed: intf != 0, file ... utilcls.h, line 2298" when running large BEA 2995 Error "bad lexical cast: source type value could not be interpreted as target" when opening RPX file created in v2.0.6 2994 "Error finding prototype from id = ''" occurs when creating Square, Spun, Micro, and Pipe piles via Pile Group Wizard 2993 Program fails to install via SCCM using SYSTEM account 2992 Avast Antivirus blocks communication between Repute and the Sentinel Licence Manager 2991 Could not connect to licence key attached to this computer, (status =42: Sentinel license manager version too old) 2990 Could not connect to a network licence key at address 10.160.5.82 (Status = 31: Requested Feature not available) 2989 Workbook's drop-down selection box does not update when calculation's name changes 2988 Default name for rock should be 'Rock 1' not 'Soil 1' 2981 Boundary Element Report does not display limiting skin friction or end bearing values 2980 Soil report does not display fcv, Eu, or Eu,max 2979 Beta value is calculated incorrectly when Option is set to Rollins et al. (for gravel) 2978 Randolph analysis does not abort when soil stiffness values are missing 2977 Cannot change the properties of a Custom Spun Pile Section (or a Custom Pipe Section) 2976 Run button should be hidden in release build of PGroupN 2973 Add note in Reference Manual that the self-weight of the pile cap is added to the loads on a pile group 2972 Error allocating memory for matrix 2971 In the Action Report, the resultant force and moment are displayed in engineering format and overflow the space allocated to them 2970 PGroupN's console window displays ** in time countdown 2969 Soil properties should report undrained stiffness as well as drained (if appropriate) 2967 Stockyard incorrectly displays panels for items that are not available 2966 The Sentinel Runtime Environment is not installed 2965 Error searching for expression: 'CustomEN1997.factor_on_shearing' 2964 Assertion failed (intf != 0 in file utilcls.h, line 2298) when dropping item from one instance of Repute to another 2958 Layer's wall friction drop-down box displays the wrong algorithms 2957 Boundary element report does not display pile cap results for linear-elastic analysis 2956 Cannot enter depth > 0 m for Standing Water Table 2955 PGroupN's title bar incorrectly states version as 2.17.5 instead of 2.17.6 2954 No error message generated when pile spacing < 1.5 D 2951 An error occurred while reading data for 'OrdnanceDatum': Error searching for expression: 'OrdnanceDatum.x_datum' 2950 An error occurred while reading data for 'Stage': The name 'Preliminary Pile Test' is already being used. Please choose a different name 2949 Force entry of IP address in correct format (xxx.xxx.x.xxx) 2946 Use Registry setting to detect presence of Sentinel drivers 2942 Output.xml does not report input values for rock k1-k5 2879 Units for extents are not written to config file (Repute2.cfg) 2623 Allow different X- and Y- spacings to be specified in the Pile Group Wizard 2332 Provide support for pre-stressed concrete spun piles with annular hole 2226 Provide summary table showing maximum values of structural effects for each pile Repute 2.5 release 1 -------------------- Version 2.5.1.17100 Released 18/08/2017 Issues fixed (5 items): 2945 Incorrect message displayed when ReAssurance has expired 2943 Reporter page of Program Options box is redundant 2910 Contents of User Manual should be revised for version 2.5 2876 Pure virtual function called when changing properties of Boundary Element Analysis 2797 Failed to load data from XML file: Repute 2.5 Release Candidate 3 (build 17087) -------------------------------------------- Version 2.5.0.17087 Released 15/08/2017 Issues fixed (7 items): 2941 Young's modulus of class C25 to C60 concretes is too low 2940 Load applied to pile group is ignored if it is not included in a Combination of Actions 2939 Layers are not listed in top-to-bottom order in Borehole's Select layers box (listed alphabetically instead) 2937 Sign of pile head rotation is displayed inconsistently 2936 No results are produced when running boundary element analysis 2932 X-rake appears in exponential format in Reporter 2701 Raise limit on concrete strength and stiffness to accomodate spun piles Repute 2.5 Release Candidate 2 (build 17085) -------------------------------------------- Version 2.5.0.17085 Released 09/08/2017 Issues fixed (16 items): 2934 Rakes are passed incorrectly to PGroupN via PGN file 2933 Rotation is displayed in different units in Reporter than elsewhere in the program 2931 Resultant moment does not display a sign in Property Inspector or Reporter 2930 Incorrect/missing data in Reporter 2929 bad_weak_ptr on entering small strain stiffness for clay soil 2928 Error message "boost::filesystem::create_directory" on running boundary element analysis 2926 Program crashes on creating pile group in Pile Group Wizard 2925 Program crashes on creating pile group containing a single pile in Pile Group Wizard 2923 Calculate pile lateral capacity in rock using expressions equivalent to those in BS 8004:2015 2920 Provide instructions for silent installation of Repute 2917 Actions are missing from report 2915 Pure virtual function called when changing soil/interface friction ratio 2844 Increase the limiting value of frictional resistance for piles in rocks above 200 kPa 2809 Allow boundary element analysis to perform ULS calculation with partial factors from design standard 2735 Store (x,y) co-ordinates of site datum 1465 A change to Poisson's ratio causes a change in E (but should change G) Repute 2.5 Release Candidate 1 (build 17080) -------------------------------------------- Version 2.5.0.17080 Released 03/08/2017 Issues fixed (25 items): 2922 Revise use of term 'rigid layer' now that support for rock has been added to the program 2921 Increase bearing pressure limit in algorithm to allow for piles bearing on rock 2918 Results for pile cap (settlement, force, moment, rotation) are missing from the Reporter 2916 Results differ between Windows and DOS version of PGroupN 2914 Assertion failed: intf != 0, file ..\utilcls.h, line 2298 2913 Input error: Layer type flag is not 1, 2, 3, or 4 2912 Contents of Quick-Start Guide should be revised for version 2.5 2911 Contents of Reference Manual should be revised for version 2.5 2909 Reporter shows unnecessary data for boundary element analysis 2908 Rock factors k1-k4 are missing from the Reporter 2907 Skin friction and bearing pressure limits are missing from the Reporter 2906 Information is missing from Reporter 2903 Program crashes when number of load increments is increased to 200 in BEM analysis 2901 Soil report does not record values of Young's modulus 2896 Disable non-linear options that are not used in boundary element analysis 2895 Program crashes on changing boundary element Stress-Strain Model to Hyperbolic 2894 Program crashes on changing Save Results flag 2893 Program crashes on re-opening project file 2892 Program crashes on changing rock layer to drained 2891 Change 'Is drained?' flag to 'Drained/Undrained' 2889 Default values of rock properties in Borehole Wizard are out of range in Property Inspector 2887 Cannot deselect 'Has Casing' flag for bored pile 2886 Mean elastic modulus for concrete should be displayed in GPa not MPa 2853 A pile with X-rake = 30 deg and Y-rake = -30 deg is incorrectly detected as an asymmetrically raked pile 2852 Cannot link Beta Algorithm to Soil Layer Repute 2.5 Beta 3 (build 17073) ------------------------------- Version 2.5.0.17073 Released 25/07/2017 Issues fixed (6 items): 2904 Increase default number of load increments in boundary element analysis to 200 2902 PGroupN engine does not use multi processor FORTRAN libraries 2900 Default value of rock k3 parameter is outside the allowable range 2898 Skin friction limit for second layer is ignored in multi-layer soil profile 2897 Reinstate ability to set global limits on skin friction and end bearing 2888 PGroupN calculation window shows strange values (è,h') Repute 2.5 Beta 2 (build 17054) ------------------------------- Version 2.5.0.17054 Released 23/06/2017 Issues fixed (11 items): 2880 Revise default layer averaging option (Poulos vs Yamashita) depending on the design situation 2878 Generated PGN file has strange values for phi/delta angles of Soil 2=sand 2877 PGN file includes an alpha value for rock, which is not needed 2876 Pure virtual function called when changing properties of Boundary Element Analysis 2875 Boundary Element Analysis displays wrong message when unable to generate PGN data for rock 2874 Program crashes changing BEA stress-strain model to hyperbolic when drainage condition is drained 2873 Problems caused by rock angle of shearing resistance of 30 degrees 2872 Borehole Wizard does not cater for invalid rock weight density 2871 Borehole Wizard does not provide facility to enter UCS for rock 2870 Borehole Wizard has not assigned rock to Layer 3 2869 Project Wizard is unable to navigate outside the Documents folder Repute 2.5 Beta 1 (build 17053) ------------------------------- Version 2.5.0.17053 Released 01/06/2017 Issues fixed (41 items): 2838 Project Manager should differentiate between calculations by using different icons 2835 Disregard specified design standard in Boundary Element Analysis created in Repute v2.0 and earlier 2834 "User options not found" appears as a Warning Message at program startup 2833 Messages should be sorted by date not time 2831 Message Board does not display duplicate messages even when generated some time apart 2830 Text is not visible on title bar on program startup on Windows 10 2829 Change default Boundary Element Analysis model to Linear Elastic 2825 Hide R factors for linear-elastic/perfectly-plastic model in Boundary Element Analysis Property Inspector 2817 Increase the available pile types in the Pile Group Wizard 2813 XML Project File does not display on Windows 10 ("Access is denied") 2811 Section is not copied when H-pile is duplicated 2808 Display name of design standard used in Longitudinal ULS calculation 2807 Cannot enter Ks value of 0.4 for normally consolidated soil 2799 Version number passed via PGN file is wrong 2796 Confusing error message on opening project: Unconfined strength of rock ... has been reset to 30 MPa (was previously 30 MPa) 2795 Program won't accept angle of shearing resistance (35 deg) within rock range (30-38 deg) 2794 Provide realistic limits to possible lengths and diameters of CFA piles 2793 Invalid cylinder strength is read on opening RPX file containing concrete with no cylinder strength specified 2784 Improve speed of program by linking with Intel's Maths Kernel Library (MKL) 2772 Promote non-linear options one level in Property Inspector for Boundary Element Analysis 2770 Stockyard shows redundant 'PipeSection' item under Pipes 2753 Check length specified for Spun Piles is possible 2737 Add C60 concrete grade 2729 Add scaling factor to combination of actions to allow < 100% of loads to be applied 2680 Relax the upper limit on dG/dz for lightly cemented sands 2673 Details of certain algorithms are missing from the Reference Manual 2603 Add square precast concrete driven piles to Pile Group Wizard 2537 Provide option to control expansion of tree view when Property Inspector is first displayed 2536 Add further pages to Program Options box, User Interface section 2487 Remove dependency on Aladdin HASP License Manager 2371 No units for Section/Diameter on second page of Pile Group Wizard 2125 Tubular piles are not available for selection in the Pile Group Wizard 2114 Provide ability to specify pile (x, y) co-ordinates by importing data from a spreadsheet 1999 Allow user to select which sections and materials appear in the Stockyard via a page in Program Options 1685 Browser page in Program Options box is redundant 1684 Units, Reports and XML pages in the Program Options box need amending 1439 Add driven concrete piles to the options available in the Pile Group Wizard 1434 Allow 'rounded' pile diameters to be entered via Pile Group Wizard 1372 Should not need to press ENTER to change check boxes settings in the Property Inspector 1326 Error loading XML document 'Output.xml' owing to ampersand '&' in Boundary Element Analysis name 1135 Project > Reset Datum does not automatically force refresh of Drawing Board Program files in the latest build --------------------------------- > indicates file has changed from the previous version Installed in C:\Program Files(x86)\Geocentrix\Repute\2.5... ----------------------------------------------------------- Actions.dll (1.22.4.1) Algorithms.dll (1.22.4.1) BearingCoefficients.dll (1.22.4.1) Boreholes.dll (3.22.4.1) > BoundaryElementEngine.dll (3.23.1.1) EarthCoefficients.dll (3.22.4.1) > Engineering.dll (4.23.1.1) > Geocentrix.dll (4.23.1.1) Interfaces.dll (3.22.4.1) Materials.dll (4.22.3.1) > Piles.dll (2.23.1.1) > Platform.dll (4.23.1.1) Project.dll (4.22.4.1) > Reports.dll (1.23.1.1) > Repute.dll (2.23.1.1) Repute1.dll (2.22.4.1) > Repute2.exe (2.5.15.1) > RexML.dll (1.23.1.1) > RexUI.dll (1.23.1.1) > Scenarios.dll (1.23.1.1) > Sections.dll (1.23.1.1) > Soils.dll (4.23.1.1) Standards.dll (3.22.4.1) Surcharges.dll (3.22.3.1) Surfaces.dll (3.22.4.1) WaterTables.dll (4.22.4.1) ***Boost dynamic link libraries*** (dated 17/08/2022) > boost_date_time-bcb32c-mt-x32-1_70.dll > boost_serialization-bcb32c-mt-x32-1_70.dll ***Embarcadero dynamic link libraries*** > borlndmm.dll (28.0.48361.3236) > cc32c280mt.dll (1.192.0.0) ***Embarcadero packages*** (dated 30/03/2023) > bcbiec280.bpl > bindengine280.bpl > dbrtl280.bpl > rtl280.bpl > vcl280.bpl > vcldb280.bpl > vcledge280.bpl > vclimg280.bpl > vclshlctrls280.bpl > vclWinX280.bpl > vclx280.bpl > xmlrtl280.bpl ***Curl libraries*** libcurl.dll (7.81.0.0) ***Developer Express packages*** (23.1.4, dated 15/08/2023) > cxExportRS28.bpl > cxGridRS28.bpl > cxLibraryRS28.bpl > cxTreeListdxBarPopupMenuRS28.bpl > cxTreeListRS28.bpl > cxVerticalGridRS28.bpl > dxBarExtItemsRS28.bpl > dxBarRS28.bpl > dxComnRS28.bpl > dxCoreRS28.bpl > dxDockingRS28.bpl > dxGDIPlusRS28.bpl > dxNavBarRS28.bpl > dxPSCoreRS28.bpl > dxPScxCommonRS28.bpl > dxPScxExtCommonRS28.bpl > dxPScxGridLnkRS28.bpl > dxPScxPCProdRS28.bpl > dxPScxTLLnkRS28.bpl > dxPScxVGridLnkRS28.bpl > dxPSdxLCLnkRS28.bpl > dxPSdxSpreadSheetRS28.bpl > dxPSLnksRS28.bpl > dxPSPrVwAdvRS28.bpl > dxPSPrVwRibbonRS28.bpl > dxPSTeeChartRS28.bpl > dxRibbonCustomizationFormRS28.bpl > dxRibbonRS28.bpl > dxServerModeRS28.bpl > dxSkinBasicRS28.bpl > dxSkinOffice2007BlackRS28.bpl > dxSkinOffice2007BlueRS28.bpl > dxSkinOffice2007GreenRS28.bpl > dxSkinOffice2007SilverRS28.bpl > dxSkinOffice2019BlackRS28.bpl > dxSkinOffice2019ColorfulRS28.bpl > dxSkinOffice2019DarkGrayRS28.bpl > dxSkinOffice2019WhiteRS28.bpl > dxSkinsCoreRS28.bpl > dxSkinWXIRS28.bpl > dxSpreadSheetCoreConditionalFormattingDialogsRS28.bpl > dxSpreadSheetCoreRS28.bpl > dxSpreadSheetRS28.bpl ***FastReport packages*** (2023.3.1, dated 20/10/2023) > frCoreLibrary28.bpl > frGraphicsLibrary28.bpl > frLocalizationLibrary28.bpl > frx28.bpl > fs28.bpl ***Intel libraries*** libiomp5md.dll (5.0.2021.1013) ***MJ Freelancing packages*** (dated 14/08/2023) > MJFClangC28.bpl (1.23.1.1) ***OCXs*** hhctrl.ocx (5.2.3790.4110) ***Raize Software packages*** (dated 11/09/2021) > DropMasterVcl280.bpl (2.5.2) ***Sentinel dynamic link libraries*** > hasps_rt.exe (29.3.27347.60001) > hasp_windows_48297.dll (9.14.27236.60001) > sntl_adminapi_windows.dll (9.0.23489.60001) > sntl_licgen_windows.dll (9.0.23426.60001) ***Steema TeeChart packages*** (dated 09/08/2023) > Tee928.bpl (9.38.230607) > TeePro928.bpl (9.38.230607) > TeeUI928.bpl (9.38.230607) TeeUser9.hlp (07/06/2007) ***other files*** Repute2.exe.manifest (10/02/2006) Help\ Repute2.chm (22/09/2009) Manuals\ Repute 2 Quick-Start Guide.pdf (16/10/2020) Repute 2 Reference Manual.pdf (28/07/2021) Repute 2 User Manual.pdf (25/03/2021) Materials\ Concretes\ AS 3600\ (all 10/11/2022) N20.xml N25.xml N32.xml N40.xml N50.xml S65.xml S80.xml S100.xml BS 8110\ (all 15/08/2017) C25.xml C30.xml C35.xml C40.xml C45.xml C50.xml C60.xml C80.xml C90.xml EN 206\ (all 22/06/2010, except where noted) C8-10.xml (15/08/2017) C12-15.xml C16-20.xml C20-25.xml C25-30.xml C30-37.xml C35-45.xml C40-50.xml C45-55.xml C50-60.xml C55-67.xml (08/12/2017) C60-75.xml (08/12/2017) C70-85.xml (08/12/2017) C80-95.xml (08/12/2017) C90-105.xml (08/12/2017) C100-115.xml (08/12/2017) Steels\ (all 27/09/2016) BS 4360 Specification for weldable structural steels\ 43.xml 50.xml 55.xml Corus\ Advance 275.xml Advance 355.xml EN 10025 Hot-rolled products of structural steel\ Legacy\ Fe360.xml Fe430.xml Fe510.xml E295.xml E335.xml E360.xml S185.xml S235.xml S275.xml S355.xml S450.xml EN 10248 Hot-rolled sheet piling of non allo steels\ S240GP.xml S270GP.xml S320GP.xml S355GP.xml S390GP.xml S430GP.xml Release Notes\ > Readme.rtf (26/10/2023) > Repute2.5.15.txt (26/10/2023) Reports\ Report.html (31/07/2006) Report.xml (16/10/2020) > ReportMaster.fr3 (2.5.15, dated 19/10/2023) > ReportTemplate.fr3 (2.5.15, dated 19/10/2023) Welcome\ Geocentrix.gif (10/05/2005) Geomarc.gif (28/11/2006) Repute.css (11/01/2017) Repute.gif (13/05/2005) Repute.html (26/05/2017) Sections\ Bearing Piles\ ArcelorMittal\ HP\ HP ### x ##.xml (44 files with various names) HZ\ HZ xxxxM xx.xml (12 files with various names) BS 4 Structural Steel Sections\ UBP ###x###x###.xml (17 files with various names) Corus\ Advance\ UKBP ###x###x###.xml (17 files with various names) Legacy\ (all 05/01/2016) UKC ###x###x###.xml (22 files with various names) European wide flange beams\ HEA\ HEA xxx.xml (14 files with various names) HEB\ HEB xxx.xml (24 files with various names) HEM\ HEM xxx.xml (14 files with various names) Pipes\ (all 17/12/2010, except *) ANSI B36 Welded and Seamless Wrought Steel Pipe\ (all 27/09/2016) NPS## x #.###.xml (various names) Corus\ (all 17/12/2016) Celcius ##.# x #.#.xml (various names) Spun Piles\ ICP\ (total of 41 sections) ICP ##A###.xml (various names) ICP ##B###.xml (various names) ICP ##C###.xml (various names) ICP ##D###.xml (various names) MS 1314 Precast concrete products\ (mainly 13/07/2016) Spun Pile ###A.xml (various names) Spun Pile ###B.xml (various names) Spun Pile ###C.xml (various names) Templates\ Blank.rpx Cancel product.xml Cancel subscription.xml haspscope.xml Licence.xml Network licence.xml Read-only memory.xml Read-write memory.xml Standalone memory.xml Subscription.xml Template for importing actions.xlsx (2.5.14, 11/11/2022) Template for importing pile groups.xlsx (2.5.14, 11/11/2022) Installed in C:\Program Files(x86)\Common Files... -------------------------------------------------- Aladdin Shared\ HASP\ 48297.xml Geocentrix\ > haspdinst.exe (9.14.16275.1) > HASPUserSetup.exe (9.14.27347.60001) Installed in C:\ProgramData\Geocentrix\Repute\2.5... ---------------------------------------------------- > ReportMaster.fr3 (2.5.15, dated 19/10/2023) > ReportTemplate.fr3 (2.5.15, dated 19/10/2023) Materials\ Concretes\ C12-15.xml C16-20.xml C20-25.xml C25-30.xml C30-37.xml C35-45.xml C40-50.xml C45-55.xml C50-60.xml Steels\ S235.xml S275.xml S355.xml S450.xml Sections\ Bearing Piles\ HP 8 x 36.xml to HP 400 x 140.xml UKBP 203x203x 45.xml to UKBP 356x356x174.xml Pipes\ NPS24 x 0.500.xml to NPS78 x 1.000.xml Spun Pipes\ Spun Pipe 250B.xml to Spun Pipe 120B.xml Installed in C:\Users\Public\Documents\Geocentrix\Repute\2.5... --------------------------------------------------------------- Benchmarks\ (all 07/11/2022, except where noted) Basile-linear (2003).rpx Basile-non-linear (2003).rpx RPT-001.rpx (07/10/2020) RPT-002.rpx (07/10/2020) RPT-004.rpx (07/10/2020) Examples\ (all 07/11/2022, except where noted) Import\ Actions after import.rpx (27/04/2021) Template for importing actions.xlsx (27/04/2021) Pile Group after import.rpx (27/04/2021) Template for importing pile groups.xlsx (27/04/2021) Bond and Harris (2008) Ex 13.1.rpx Fleming (1992).rpx Large circular group.rpx Randolph analaysis (Fleming at al Chapter 4 Example 1).rpx Tomlinson (1994).rpx Tutorials\ (all 07/11/2022, except where noted) Tutorial 1\ Step1.rpx Step2.rpx Step3.rpx Step4.rpx Step5.rpx Step6.rpx Tutorial 1.rpx Tutorial 2\ Step1.rpx Step2.rpx Step3.rpx Step4.rpx Step5.rpx Step6.rpx Tutorial 2.rpx Tutorial 3\ Step1.rpx Step2.rpx Step3.rpx Step4.rpx Step5.rpx Step6.rpx Step7.rpx Tutorial 3.rpx Tutorial 4\ Step1.rpx Step2.rpx Step3.rpx Step4.rpx Step5.rpx Step6.rpx Tutorial 4.rpx Tutorial 5\ Step1.rpx Step2.rpx Step3.rpx Step4.rpx Step5.rpx Step6.rpx Tutorial 5.rpx Tutorial 5.xlsx (19/12/2019) Tutorial 6\ Step1.rpx Step2.rpx Step3.rpx Step4.rpx Tutorial 4.rpx Tutorial 6.rpx ------------------------------- End of release notes -------------------------------